24/7 emergency boiler breakdowns · 01268 2644602026 prices · VAT included ↗
All gas and boiler work is carried out by Gas Safe registered engineers.*Selected models and qualifying installer schemes only. Model, filter, registration and servicing conditions apply; your quote confirms the eligible term.
INSTALLATION PLANNING / BOILER GUIDE

What size boiler does your home actually need?

Boiler output should reflect the building’s heat loss and how hot water is delivered; bedroom count alone is a poor sizing method.

By Essex Home BoilersUpdated 11 November 2026
THE SHORT ANSWER

A suitable boiler is selected using the property’s heating requirements and hot-water arrangements. A combi’s hot-water output and a system boiler’s space-heating output solve different problems.

Heat demand is not a bedroom count

Two three-bedroom houses can lose heat at very different rates. Insulation, window area, draughts, exposed walls, ceiling heights and the temperature you want indoors all influence the heating load.

Extensions and open-plan alterations matter too. A well-insulated addition may add less demand than a colder older room of similar size. A room-by-room heat-loss assessment is more useful than choosing a boiler by floor area alone.

  • Insulation and glazing
  • Room sizes and design temperatures
  • Radiator or underfloor heating output

Combi hot-water performance is a separate decision

A combi heats water as it is used. Its hot-water flow capability may drive the model selection more than the amount of heat needed by radiators. Increasing the number on the box cannot create mains water pressure that the property does not have.

Ask what flow is available at the property and how performance changes when another tap or shower opens. A larger combi is not a reliable fix for weak incoming water supply.

Stored hot water changes the calculation

A system or conventional boiler can supply a cylinder, giving a different way to meet several simultaneous hot-water demands. Cylinder capacity, recovery time, controls and available space all count.

This makes cylinder condition and the household routine relevant to the specification. Removing a cylinder simply to gain cupboard space can be the wrong trade-off for a busy family bathroom.

Radiators and controls still need to match

A boiler can only heat rooms effectively when the emitters and circulation system can deliver enough heat. Undersized radiators, poorly balanced circuits and unsuitable controls can make a correct boiler seem inadequate.

Discuss heating performance as a complete system, especially if you would like more efficient low-temperature operation rather than a simple appliance exchange.

The practical question to ask your installer

Ask what evidence was used to select the heating output and, for a combi, the hot-water performance. A confident answer should be specific to the home and its water supply.

We can begin with your postcode, room layout, boiler details and the number of bathrooms before deciding what further checks the job needs.

BEFORE YOU REQUEST A QUOTE

Information worth having ready

  • Home layout and approximate room areas
  • Age and state of insulation
  • Current radiator performance
  • Number of simultaneous showers
  • Available mains water flow
  • Any extension or new heating zone
QUESTIONS WE HEAR

Frequently asked questions

Is a higher kW boiler always better?

No. Space-heating demand and hot-water needs must be considered separately. Oversizing can be unnecessary; an installer should explain the selected output.

Will a new boiler solve cold rooms?

Not automatically. Radiator output, circulation, valves and controls may be the cause and should be checked as part of the system.

Further reading and safety information

Useful independent guidance for planning your project:

These are general planning guides, not a remote diagnosis or substitute for an inspection. All gas and boiler work is carried out by Gas Safe registered engineers.

Before you book

How do I get a fixed boiler installation price?

Complete our short quote request with your current boiler, bedrooms, bathrooms and postcode. Typical VAT-inclusive guide ranges are £1,995–£3,200 for a combi swap and £3,000–£4,500 for a system or regular boiler conversion to a combi. We check the property and installation scope, then confirm your fixed quotation before you agree to the work.

Can I call for an emergency boiler breakdown at night?

Yes. Call Essex Home Boilers on 01268 264460 for 24/7 emergency breakdown cover. Ask for the earliest available visit and the call-out charge. Same-day attendance depends on engineer availability and your location; completing a repair also depends on the fault and parts.

Where is Essex Home Boilers based?

Essex Home Boilers is based at 103 Pound Lane, Bowers Gifford, Basildon, Essex, SS13 2HN. Call 01268 264460. We cover Essex and surrounding areas; appointments and coverage are confirmed for your postcode.